Example projects · Demos

Example Projects in Photonics, Test Systems and Control Engineering

Real systems we designed, built and proved, from the first requirement to a tested instrument.

Each story shows the problem, the design decision that solved it and the instrument or product it led to. Filter by field, watch the demos, and open any project for the full write-up.

ISO 9001:2015Optics + electronics + softwareLab to production lineUV to LWIR
Spectro-radiometer channels during assembly and alignment in the IZAK lab
Spectro-radiometer channels during assembly and alignment in our lab.

See it working

Short demos from real systems

Recordings of IZAK instruments doing the work they were built for.

Laser beam profiler: basic operationLive beam image, size, position and shape from UV to LWIR.
Laser beam profiler: Test and ReportPass/fail limits and a report for every unit on the line.
AI Analytics and IZAK Insight ChatTrends across stations and batches, asked in plain language.

Medical device demos (all-in-one laser test, fractional laser profiling, IPL calibration and fiber ferrule inspection) are on the Medical Device page

Project examples

Problems we solved, and how

Twelve project stories across lasers, spectroscopy, fiber optics, electronics production and control engineering.

IZAK multi-channel spectro-radiometer with three telescope channels

Spectroscopy · Defense EO

A multi-channel spectro-radiometer with three telescopes

Challenge
Measure the spectrum of a distant source in several bands at the same moment, including fast events, with the same reading wherever the target sits in the field of view.
What we did
Three telescope channels, each with its own spectrometer and detector, aligned to one line of sight. A field lens in each channel keeps the response within 10% across the field; neutral-density filters extend the dynamic range.
Result
It became a product: the IZAK Multi-Channel Spectro-Radiometer.
Spectro-radiometer
Beam profiler software showing measured beam values

Industrial lasers · Production test

A CO₂ laser test jig that became an LWIR beam profiler

Challenge
Small batch-to-batch variations in mounts and optics cause tilt, decentring and spacing errors. Every 10.6 µm CO₂ laser had to be checked before shipping, at low cost.
What we did
A test jig with a low-cost, adaptable beam profiler and software that measures the beam and reports pass or fail for each unit.
Result
The design grew into the IZAK LWIR beam profiler for 7.7–12 µm.
Laser beam profilers
IZAK multi-channel power meter with five optical fibers

High-power lasers · Fiber

Multi-channel power meter for high-power lasers

Challenge
Measure the power of several fiber-delivered laser channels at the same time, at high power, and use the same set-up to align and focus narrow beams.
What we did
Five fiber-coupled channels with SMA interfaces, up to 50 W per channel, measured in parallel with logging. A narrow-beam adapter probe images beams of tens to hundreds of microns for alignment and focus checks on the fiber ferrule.
Result
A ready instrument for parallel power measurement and SMA alignment.
Watch the video Five channels, 200 nm–20 µm
Power meter module
LED and screen inspection system with its cover open, showing the unit under test

Electronics production · LED test

Screen and LED tester with on-board OCR

Challenge
Every unit has about twenty LEDs, each able to run at different wavelengths, and a seven-digit display. Colour, intensity and the displayed text all had to be verified automatically.
What we did
Automated hardware and software test equipment: an imaging system with image processing and spectral information for colorimetric LED testing, OCR of the display, and robot arms that press the buttons. A closed cover keeps ambient light out.
Result
Each run writes LED colour, LED ID and recognised text to an output file.
Watch the video Related demo: LED colour and position test
Radiometry and LED quality
Optical fiber inspection with image processing after cleaving

Fiber production

Fiber incision and inspection tester

Challenge
Fiber production needs fast, repeatable checks of fiber pitch, height after cleaving and cleave angle, at the line.
What we did
A microscope and camera station with image analysis that measures the fiber geometry after cleaving and logs every result.
Result
Inspection and transmission testers for fiber production lines.
Fiber inspection testers
IZAK fiber ferrule inspection system

Fiber optics · Connectors

Fiber ferrule inspection system

Challenge
A fiber connection is only as good as its ferrule: adhesive symmetry, core centring and a clean end face decide the loss.
What we did
High-resolution imaging of the ferrule end face that measures core centre offset and adhesive symmetry, detects contamination and defects, and checks transmittance.
Result
A product, also shown in our demos.
Watch the video Concentricity, transmission and end-face quality
Ferrule inspection system
Relay optics coupling light into a spectrometer entrance slit

Spectroscopy · Fiber optics

Coupling light into a spectrometer slit and into fiber

Challenge
A spectrometer only sees the light that passes its narrow slit at the right angle, and fiber coupling depends on numerical aperture, spot size and alignment. A small mismatch costs most of the signal.
What we did
Relay optics that image the source onto the slit and match the acceptance angle; for fiber, matched NA and spot size, couplers, collimators and taps that sample a known fraction of the light.
Result
Used in every channel of our spectro-radiometers and fiber testers.
Optical design projects
Uniform laser illumination pattern from laser diodes

Photonics R&D · Illumination

Uniform illumination from laser diodes

Challenge
Laser-diode beams are elliptical and divergent. A simple lens gives a hot spot, not a uniform area.
What we did
Early prototypes from off-the-shelf optics, each iteration measured with a beam profiler, converging quickly on a layout with a uniform field.
Result
A fast prototype-and-measure loop with our own beam profilers.
Laser beam profilers
FPGAFeedback · timing · reconfigurable

Control engineering · FPGA

FPGA control in an electro-optics set-up

Challenge
Fast prototyping of an electro-optical set-up needs firmware that can change as quickly as the experiment does.
What we did
An FPGA that rewires to implement the function: feedback-loop control, design parameters that can be reconfigured, basic hardware testing, and control of scan angle, power source and detector settings.
Result
Control that moves from the lab bench to the embedded system.
Read the project
Ultrasonic flow meter development set-up

Control engineering · LabVIEW

Ultrasonic flow meter development support

Challenge
An ultrasonic flow meter under development needed one place to run the system, see the data and repeat the tests.
What we did
Command and control of the whole system in a LabVIEW software application.
Result
A test bench the development team could run every day.
Read the project
Thermodynamic heat engine research prototype

Research prototype · Control

Thermodynamic heat engine prototype

Challenge
A research team needed a working prototype to study a thermodynamic heat engine, with every signal measured and logged.
What we did
Custom printed circuit boards and power supplies, programmed microcontrollers, and integration of sensors, detectors, engines, pumps, generators, slip rings and A/D converters. A LabVIEW application for command, control, graphs and a log file, and the packaging.
Result
A complete, instrumented research prototype.
Read the project
AI analytics dashboard for IZAK laser beam profiler data

Software · Production data

AI analytics for beam profiling data

Challenge
Production and R&D teams collect thousands of beam measurements but look at them one at a time.
What we did
Statistics, trends and correlations across stations, batches and product families, a beam image viewer, report drill-down, a chat that queries the database in plain language, and scheduled email reports.
Result
Available with IZAK laser beam profilers.
Watch the video Trends and questions over beam data
AI analytics article

Built on our own instruments

The products behind the projects

We measure with instruments we build and know inside out. When a project needs a measurement that does not exist yet, it often becomes the next product.

UV–VIS–NIR300–1100 nmSWIRup to 2.05 µmMWIR1.5–5.7 µmLWIR7.7–12 µm

FAQ

Questions about our projects

What kind of projects does IZAK Scientific take on?

Optical and electro-optical design, test and inspection systems, and control engineering. Most projects start with a measurement problem: a beam, a spectrum, a fiber or a display that must be measured or verified, in the lab or on a production line.

Can a one-off lab measurement become a production test station?

Yes. Several projects on this page started as a lab measurement and became a production test jig: the fixture, the measurement instrument, and software with pass/fail limits and reports.

Do you write the control software too?

Yes. We write command-and-control software in LabVIEW, program microcontrollers and FPGAs, and design the electronics and power supplies the system needs.

Which wavelengths can your instruments measure?

Our laser beam profilers cover UV–VIS–NIR from 300 to 1100 nm, SWIR up to 2.05 µm, MWIR from 1.5 to 5.7 µm and LWIR from 7.7 to 12 µm. For spectral work we build multi-channel spectro-radiometers matched to the bands of the project.

Where are the medical device projects?

Laser and IPL calibration, fractional laser profiling and other medical device work are on the Medical Device page, with their own demos.

How do we start?

Book a 20-minute call or describe the project in the contact form: what must be measured or controlled, the wavelength or band, power or energy, the environment and what the result must prove. We reply with the questions that matter and a proposed approach.

Next step

Have a measurement or control problem?

Tell us what must be measured, controlled or proved. We reply with the questions that matter and a proposed approach.

  • What must be measured or controlled
  • Wavelength or spectral band
  • Power, energy or signal levels
  • Lab, production line or field
  • What the result must prove
Get new IZAK guides and free calculators by email, one short email a month: Subscribe · Privacy Policy
Skip to content